Vinyl plank floors are becoming increasingly popular today. People use them not only in their homes but also in commercial places. So if you're planning on installing it instead, you might be wondering:"How long does it take to install vinyl plank floors?"You will get your answer in the article.
For an average sized room, it would only take a few hours to install a vinyl plank floor. However, on average it would take around 24-48 hours. In addition, it can also take a few weeks or months depending on the size and condition of the room, as well as the condition of the flooring in the room.
Even after the installation process is complete, a vinyl plank floor may not be suitable for all types of loads. So in this article I'm going to take a look at how long it can take to install a vinyl plank floor, along with other information you may find helpful.
How long does it take to install vinyl plank floors?
On average, vinyl flooring takes about one to two days to install. Before installation, these vinyl floors need a few days to get used to the humidity and temperature in your home.
Vinyl plank floors can take anywhere from a few hours to a few days to fully cure. It may also take a few weeks or months to resolve depending on the circumstances. Vinyl floors take longer to cure if you install them on an uneven surface. For this reason, vinyl planks should be installed with care over concrete or tile floors.
You should check this first before installing vinyl plank floors. To do this, take a piece of vinyl. Then seal all corners with tape before placing it. Now let the old vinyl rest for 3 days. If the masking tape peels off easily afterwards, your floor is too wet for vinyl floors.
You also need to give your vinyl plank floor time to adjust to the ambient temperature of the area that is assigned to the installation. Therefore, put the boards in the desired room and leave them there for at least 2 days.
Also, use the grader to inspect the subfloor to ensure the vinyl plank flooring fits smoothly. Using this level would help you spot any bulges or indentations that need to be repaired before placement. This prevents the floor from warping when set.
Well, click types of vinyl floors that cure quickly and are ready to use. However, you must wait at least 2 days for glued floorboards to harden before you can fully walk on them.
On the other hand, urethane adhesives take about 15 hours for moderate traffic. However, you can wait at least a day before putting the furniture. But the vinyl decal will take about the same time as the glued ones to be ready for you to apply, that's about 48 hours.
How do you lay vinyl floorboards?
Whether you install vinyl plank flooring yourself or let a professional do the job, there are a few steps you need to follow to successfully complete the installation process. Now let's discuss the installation steps for vinyl floorboards:
Step 1: Measure the surface of your floor
Start by calculating the area you need to cover. This way you get the right amount of profile. Therefore, first calculate the length and width of the room. And then multiply those two numbers together. The area of your room determines whether the rooms are rectangular or square.
If your room is uneven in size, divide it into small squares and rectangles. Then find the surface of each. After that, add them all together to get the sum.
Step 2: Create a layout design
After that, select the direction you want the boards to go. Also consider where you will place each row. You don't want a line that's too narrow at one end.
To avoid weak points, stagger all joints. Between rows, many professionals recommend staggering the links by at least 6 inches.
However, before you start, it is better to draw the layout. You can also lay the flooring first before laying it once you have it. It's a fantastic way to see how everything will look when it's done.
Step 3: Preparing the Floor
Before starting work, leave the vinyl floor in the room where it is to be installed for at least 2 days. This gives the panels time to get used to the ambient temperature and humidity.
Also make sure the subfloor is flat and clean. Use a spirit level to confirm that the deviation is no more than 3/16 inch at 10 feet. If there are uneven areas, use self-levelers to even out low spots and sand or grind high spots.
Also, use a crowbar to remove any baseboards on the floor. If they're stuck to the walls with paint, use a box cutter carefully around the edges.
Step 4 - Lay the vinyl planks on the floor
Please note that the walls are not always straight. Therefore, it is better to stick to the chalk line. In order to create a perfectly straight line, it may be necessary to cut the first row of planks. If that's the case, just using a circular saw will suffice. You can break most boards. However, using the hacksaw will give a cleaner finish.
Place the tabs of the next board into the groove of the first board once it is in place. Use the rubber mallet and knocking block to press down firmly.
Step 5 - Lay the last plank in the row
It is a bit more difficult to place the final table in each row. First determine the required length. Then use a frame square to define the cutting line. After that mark and break the board. If that doesn't fit perfectly, use your flat saw to cut it down.
You will need to attach the tab and secure it in place with a drawbar tool. You have to repeat the whole process for each row. However, stagger the connections at random angles for a more natural look.
Step 6: Completion
Now it's time to nail the shoe shape or turn it a quarter turn into position. But don't forget to connect it to the wall, not the floor. Finally, apply the transition varnish to any edge between the other floors and the new floor.
How much does it cost to lay vinyl flooring?
Vinyl plank floors cost about $4 to $12 per square foot if you hire a professional to do the job. The average cost to install good quality waterproof or waterproof plank flooring is $6 to $8, which means installing 1,000 square feet of vinyl plank flooring costs an average of $5,500 to $8,000.
Many factors go into the cost of installing vinyl flooring. The biggest cost factor is the price of the type of vinyl plank. Well, the cheapest boards cost around$ 1,19for every square meter.
The average cost of high-quality vinyl records, on the other hand, is up to$ 5,29for every square meter. Due to the higher durability, these higher-quality alternatives are often used in high-traffic residential or commercial areas.
In addition, labor costs for the installation process also differ, as well as material prices. Doing the work yourself can save you some money here.
However, to hire a professional for the installation process, the overall cost of the installation process would be higher. The amount the professionals would charge depends on the size and condition of your room.
If you need to replace old flooring, labor costs can range from 35 cents to $4 per square foot, depending on the type of flooring you need to remove.
Also, the size of your room, your project plan, the type of floor, etc. it would also affect the overall cost of installing vinyl flooring.
Installing vinyl floors is very easy. You now have your answer to the question,"How long does it take to install vinyl plank floors?"I also discussed the steps and cost of the installation process.
Thank you for reading. I hope you found this article useful. Much luck!